{"product_id":"zinsser-covers-up-paint-aerosol-400ml","title":"Zinsser Covers Up Paint - Aerosol 400ml","description":"\u003ch1\u003eOverview\u003c\/h1\u003e \u003cp\u003eZinsser Covers Up is a low odour solvent-based aerosol that is a stain killer and touch up paint all in one. Formulated to block and seal most common ceiling stains in a flat white finish that will blend with most acoustic ceiling tiles and white paints. It can be used under and over water and oil based paints.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCovers water, nicotine, smoke and graffiti\u003c\/li\u003e\n\u003cli\u003eLow odour\u003c\/li\u003e\n\u003cli\u003eNon-yellowing\u003c\/li\u003e\n\u003cli\u003ePerfect spot 'touch up' paint\u003c\/li\u003e\n\u003c\/ul\u003e \u003ctable\u003e\n\u003ctd\u003eArea\u003c\/td\u003e\n\u003ctd\u003eInterior\u003c\/td\u003e\n\u003ctr\u003e\n\u003ctd\u003eRecommended Use\u003c\/td\u003e\n\u003ctd\u003eInterior acoustic ceiling tiles or painted ceilings, light fixtures, HVAC ductwork and vents, overhead pipes and conduit, or anywhere an overhead high hiding stain sealing primer or spot finish is needed.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBase\u003c\/td\u003e\n\u003ctd\u003eSolvent-Based\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCoverage\u003c\/td\u003e\n\u003ctd\u003eUp to 1.5m² per litre\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDrying Time\u003c\/td\u003e\n\u003ctd\u003e30 Minutes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRe-Coat Time\u003c\/td\u003e\n\u003ctd\u003e2 Hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRecommended Coats\u003c\/td\u003e\n\u003ctd\u003e1 Coat\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eApplication Method\u003c\/td\u003e\n\u003ctd\u003eAerosol\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePreparation\u003c\/h2\u003e\u003cp\u003eBefore application, ensure all surfaces are clean, dry, and sound. Free from dust, dirt, excessive chalk, grime, grease, oil, wax, mildew, wallpaper adhesive, or any contaminants that may affect adhesion. If in doubt, wash the surface using a solution of household ammonia and water or another appropriate cleaning product. Avoid using tri-sodium phosphate (TSP) based cleaners.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRemove any loose or flaking coatings by scraping or sanding.\u003c\/li\u003e\n\u003cli\u003eFeather the edges of any remaining paint to create a smooth transition to bare surfaces.\u003c\/li\u003e\n\u003cli\u003eTreat any existing stains by washing, sanding, or scraping as needed.\u003c\/li\u003e\n\u003cli\u003eRemove mildew from interior surfaces using a mildew remover such as Zinsser Mould Killer \u0026amp; Remover.\u003c\/li\u003e\n\u003cli\u003eCountersink exposed nails, then spot-prime and fill.\u003c\/li\u003e\n\u003cli\u003eUse a wire brush on rusty areas to remove loose rust before priming.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication\u003c\/h2\u003e\u003cp\u003eFor best results, follow these step-by-step instructions when applying this aerosol product:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eShake Well Before and During Use: Before application, shake the can vigorously until the mixing ball inside begins to rattle, then continue shaking for at least one full minute. This ensures the product is properly mixed for consistent performance. Shake the can periodically during use to maintain an even spray and prevent clogging.\u003c\/li\u003e\n\u003cli\u003eTest Spray Pattern: Always test the spray pattern on a piece of scrap material or cardboard before beginning your project. This helps ensure you’re familiar with the spray control and provides a preview of the coverage.\u003c\/li\u003e\n\u003cli\u003eMask Off Surrounding Areas: To protect adjacent surfaces, mask off nearby objects or areas not intended for treatment. This will help you achieve clean edges and reduce overspray.\u003c\/li\u003e\n\u003cli\u003eMaintain Proper Spray Distance: Hold the can 25–30 cm (10–12 inches) from the surface. Apply using light, even ‘dusting’ strokes, moving the can steadily across the surface to avoid drips, pooling, or uneven coverage.\u003c\/li\u003e\n\u003cli\u003eTip: Several light coats provide better results than one heavy coat.\u003c\/li\u003e\n\u003cli\u003eCleaning After Use: After spraying, clear the nozzle by inverting the can (holding it upside down) and spraying until only clear gas comes out. This prevents the nozzle from clogging between uses.\u003c\/li\u003e\n\u003cli\u003eIf the spray tip becomes blocked, remove it carefully and clean with a pin or needle. Do not insert objects into the valve opening.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Zinsser","offers":[{"title":"Default Title","offer_id":57447770554534,"sku":"qcb1789759802458","price":10.69,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0745\/7649\/4758\/files\/zinsser-covers-up-paint---aerosol-400ml_1.jpg?v=1789759807","url":"https:\/\/printmotifwear.shop\/products\/zinsser-covers-up-paint-aerosol-400ml","provider":"My Store","version":"1.0","type":"link"}